MAGNECOR SPARKPLUG WIRES

MAGNECOR SPARKPLUG WIRES

Since 1976, Magnecor has been a manufacturer and supplier of ignition wires used for competition, street, industrial and military applications. Magnecor is able to provide a spark plug wire set and individual wires for almost every engine ever made using a variety of technically advanced long-service-life ignition cables. Magnecor is a manufacturer of technically advanced ignition wires (spark plug wires, ignition leads, high tension leads). Magnecor head office and factory are situated in Farmington Hills, Michigan, USA (Detroit metro area). If you are needing spark plug wires for almost any engine, or industrial application, including custom specification wire sets, individual wires or cable and parts, more than likely, we can help you.

MAGNECOR RACE WIRES


KV85 COMPETITION 8.5mm IGNITION CABLES: Magnecor's KV85 Competition (8.5mm) and R-100 Racing (10mm) Ignition Cables feature Magnecor's exclusive 2.5mm high capacity Metallic Inductance EMI Suppressed conductor consisting of stainless steel wire precisely wound at 200 turns per inch over a ferrimagnetic core. The insulating jacket is made entirely of Magnecor's exclusive TC-1500-HS high strength aerospace grade silicone rubber, and its single layer construction will prolong the jacket's insulating ability by conducting extreme heat away from hot-spots that occur near over-the-limit heat sources. The KV85 8.5mm jacket has a service heat resistance of 600 degrees F (320 degrees C) and up to 1,000 degrees F (540 degrees C) for short burst 3 minutes. The R-100 10mm jacket has a service heat resistance of 700 degrees F (380 degrees C) and up to 1,200 degrees F (650 degrees C) for short burst 3 minutes. Even if limits are exceeded, the silicone rubber will retain its insulating ability until wires are removed from engine. Magnecor Race Wires are primarily designed and constructed to be used in applications where it is essential to prevent the possibility of ignition wires compromising engine performance. Modern race engines, modified street engines and stock street engines which rely on electronic devices to control the function of either or both the ignition and fuel systems are prone to interference from all other spiral conductor ignition wires sold through performance parts outlets, none of which can provide proper suppression for EMI, particularly if a high-output ignition system is used. We always recommend use of our Race Wires for any stock or modified late model street engine that is electronically managed, however most other modified or street engines can also use our Race Wires to improve ignition performance
R-100 RACING 10mm IGNITION CABLES: Magnecor's KV85 Competition (8.5mm) and R-100 Racing (10mm) Ignition Cables feature Magnecor's exclusive 2.5mm high capacity Metallic Inductance EMI Suppressed conductor consisting of stainless steel wire precisely wound at 200 turns per inch over a ferrimagnetic core. The insulating jacket is made entirely of Magnecor's exclusive TC-1500-HS high strength aerospace grade silicone rubber, and its single layer construction will prolong the jacket's insulating ability by conducting extreme heat away from hot-spots that occur near over-the-limit heat sources. The KV85 8.5mm jacket has a service heat resistance of 600 degrees F (320 degrees C) and up to 1,000 degrees F (540 degrees C) for short burst 3 minutes. The R-100 10mm jacket has a service heat resistance of 700 degrees F (380 degrees C) and up to 1,200 degrees F (650 degrees C) for short burst 3 minutes. Even if limits are exceeded, the silicone rubber will retain its insulating ability until wires are removed from engine. Magnecor Race Wires are primarily designed and constructed to be used in applications where it is essential to prevent the possibility of ignition wires compromising engine performance. Modern race engines, modified street engines and stock street engines which rely on electronic devices to control the function of either or both the ignition and fuel systems are prone to interference from all other spiral conductor ignition wires sold through performance parts outlets, none of which can provide proper suppression for EMI, particularly if a high-output ignition system is used. We always recommend use of our Race Wires for any stock or modified late model street engine that is electronically managed, however most other modified or street engines can also use our Race Wires to improve ignition performance

MAGNECOR CONVENTIONAL HIGH PERFORMANCE WIRES

ELECTROSPORTS SERIES 7mm and 8mm IGNITION CABLES: Magnecor 7mm Electrosports 70 Ignition Cables
Direct replacement for 7mm original equipment carbon conductor wires. Conductor provides exceptional RFI and EMI suppression to permanently eliminate the typical performance and fuel-wasting spark energy deterioration of OE and aftermarket carbon conductor wires. Also overcomes performance problems associated with poorly suppressed aftermarket spiral conductor wires on both modern and older engines. The conventional style insulating jacket consists of EPDM insulation and an extra strong EVA outer jacket for better terminal retention needed for small diameter cables.
Magnecor 8mm Electrosports 80 Ignition Cables
Original equipment replacement. Designed to improve original ignition system performance on street vehicles using either electronic engine management systems or carburetors. Conductor provides excellent RFI and EMI suppression to permanently eliminate the typical performance and fuel-wasting spark energy deterioration of OE and aftermarket carbon conductor wires. Also overcomes performance problems associated with poorly suppressed aftermarket spiral conductor wires on both modern and older engines. The conventional style insulating jacket consists of high dielectric strength silicone rubber insulation, fiberglass reinforcing braiding and a high temperature, high tear strength silicone rubber outer jacket. The flexibility and ruggedness of the cable allows it to be fitted into original 7mm cable holders. Ideal for use on heat-generating LPG (propane) gas conversion engines.
7mm unsuppressed copper conductor IGNITION CABLES: The conventional style insulating jacket consists of EPDM insulation, fiberglass reinforcing braiding and a black silicone rubber outer jacket. The stranded tin-plated copper conductor provides no suppression. Made for industrial applications, restorations, older race car engines, industrial engines and other applications where suppression is not needed. This type of cable is illegal for street use in most countries on a automobile unless resistance-type suppressors are attached to provide RFI suppression (as on many German made vehicles). The jacket on this cable is unprinted. We can make wire sets or individual leads using this ignition cable to any length or style needed by the customer. Cable itself can be ordered loose in any length, or in custom lengths or packaging for industrial applications (please inquire). Meets SAE-J2031 Type 1 Class "E" requirements. This cable is very popular with owners of older German vehicles want to replace the deteriorated lower grade cable used with the original connector/suppressors on their engine with a high grade silicone rubber jacketed cable.

MAGNECOR SPECIAL APPLICATION WIRES

CN Series KV85 COMPETITION 8.5mm IGNITION CABLES: Magnecor's CN Series: 8.5mm KV85 Competition and 10mm R-100 Racing Ignition Cables feature Magnecor's exclusive 2.5mm Metallic Inductance Suppressed CN25 conductor, consisting of a special alloy wire precisely wound at 200 turns per inch over a ferrimagnetic core. These ignition wires are specifically designed and constructed to overcome the severe RFI problems associated with spiral conductor ignition wires, making them an ideal choice for vehicles in which Ham radios, telephone and TV equipment, 2-way radios, off-shore communication equipment, and high powered sound equipment etc. is installed. High capacity conductor eliminates the spark energy reduction associated with all "suppression" ignition wires and supplementary suppressors normally used to solve severe RFI problems.
CN Series R-100 RACING 10mm IGNITION CABLES: Magnecor's CN Series: 8.5mm KV85 Competition and 10mm R-100 Racing Ignition Cables feature Magnecor's exclusive 2.5mm Metallic Inductance Suppressed CN25 conductor, consisting of a special alloy wire precisely wound at 200 turns per inch over a ferrimagnetic core. These ignition wires are specifically designed and constructed to overcome the severe RFI problems associated with spiral conductor ignition wires, making them an ideal choice for vehicles in which Ham radios, telephone and TV equipment, 2-way radios, off-shore communication equipment, and high powered sound equipment etc. is installed. High capacity conductor eliminates the spark energy reduction associated with all "suppression" ignition wires and supplementary suppressors normally used to solve severe RFI problems.